Pavati tells you that you are getting the best drift boat made. Make sure you take a look at a PAVATI before you buy another drift boat.

PAVATI is a company built on the experiences and desires of people who want the best. Our lineup of standard features reflects that commitment like no other boat company can. The PAVATI experience isn't simply about building the best boat we can, but providing the most enjoyable and rewarding fishing experience available. New for 2011, PAVATI Introduces it's new flagship -- The "LEGACY". The first all aluminum drifter built specifically for the expert fly fisherman. Constructed with the newest technologies and part hand-craftsmanship, no detail has been forgotten. Snag-free casting areas, padded fly-fishing saddles, single hand rod tubes, up to 14' Spey rod holders, super quiet and slippery bottoms, and easy in and out doors. This boat is an expert fly fisherman's best friend.


When you're fly fishing it's nice to have some level standing room. Plus, it's very important to the Captain of the ship that the boat be level front to rear and side to side. Drift boats in particular, perform the best in this situation. Move all three seats, foot rest, and the rod holder to accommodate the type of fishing you're doing. Fly fish in the morning, use the 3-in-a-row setup then take the family for a ride in the afternoon using three seats in the front. Bait fish the next morning using two seats in the front. Versatile = PAVATI drift boats.


When it comes to comfort, PAVATI Marine wanted to make sure your valuable fly fishing time was well spent.

Black and blue marks on your body from being beat against a couple pieces of bent pipe should not be part of the program.

So, we asked our engineering department to use lots of padding when designing our fly fishing stands. These durable units are easy to install and easy to take out... When you're not using them, in the garage or under the seat they go.

A snug fit and comfort are key to standing up for long periods. After all, we're supposed to be having fun!




PATENTED QUICK LOCK SEAT SYSTEM

The Quick-Lock Seat system is the easiest most customizable seat system available in ANY boat today-PERIOD.

In a matter of seconds, with no tools required, you can completely rearrange a PAVATI to adjust for weight and/or different fishing styles on the fly.

Move seats from side to side or from front to back to adjust weight for optimal balance and rowing comfort.

Add or remove seats to lighten the load or add an additional fisherman. Put a seat in the back and offset it to run a kicker motor. And it's not just the seats...

Reposition your foot rest exactly where you want it, add Heater systems, Tackle boxes, Rod holders and other accessories that all work with the same simple system.

An added bonus with the Quick-lock Seat System is the seats are much lighter than your ordinary old school bench row seat.



Drift Boat Doors

Doors are the ticket when you're in a drift boat and wearing chest waders. They allow some folks the luxury of even being able to go.

Seat Storage

Be ready for those rainy days with a place to stow your rain-gear. Our seat boxes are water tight and great for storing essential items. Hats, sun screen, towels, or even lunch. Not to mention a nice place to sit while cruising to the next fishing hole. Put it in the perfect spot for back trolling with a kicker or electric motor or take it out completely.


PAVATI's overstuffed fly fishing saddles add to a relaxing day on the water...

This front saddle installs in less than a minute.


PAVATI'S EXCLUSIVE NO EXTRUSION SEAMS

Since its first hull hit the water, PAVATI has been obsessed with performance at every angle. This is evident in our industry exclusive "No extruded seams" construction. The old boat makers have been using the same extruded cap construction for more than 40 years. It has worked fine, but was heavy and needed improvement. Only recently has the CNC cut, computer designed edge to edge manufacturing been possible, and PAVATI has embraced it fully. Using state of the art software PAVATI's engineers have pushed the envelope once again by eliminated the extruded caps on every seam of a traditional aluminum drifter. This cuts out weight- lots of weight. It also eliminates the external chine's that are so notorious for grabbing currents and rocks. We put the strength where you need it -- not where you don't. Our boat has a "Hard Chine" that tracks better than any boat on the market, is lighter weight, yet still has an internal chine extrusion WITH 4 FULL LENGTH WELDS that gives you the strength you need to bounce off of rocks for years without worry. Look close at a PAVATI's seams and you will see a cleaner boat that is ready to slide off of rocks and slide through the water.


ULTRA-FLOW RADIUS TRANSOM

PAVATI is the only aluminum drift boat manufacturer with this feature. Although like most of PAVATI's unique features it does take more manufacturing time, the rounded transom has major benefits that far out weigh the extra labor. First and foremost- this makes a better rowing boat. The computer designed rounded transom creates lift- not drag. The old "tombstone" flat transoms require the drift boat to have much more rocker in the rear of the boat.

If they didn't, the transom would basically be a sail grabbing water and making it almost impossible to row. Our engineers found that the Ultra-Flow transom does the opposite (creates lift) - which allow us to lay the transom back down a little. This generates much more room in the back of the boat for a fisherman and/or coolers and gear.

Another benefit is the boat rides higher -- also reducing drag and enabling the boat to run shallower water. When the boat was drawn up PAVATI's designers also created a one-piece bottom and transom. This eliminated the seam that every other aluminum drift boat builder has on there transom. This also eliminates the piece of extruded aluminum stock they use to cap the seam- cutting down weight and a doing away with a weak point.


3 SUPER SLICK & TOUGH BOTTOM OPTIONS

We rewrote the book on drift boat bottoms. Not only do we give you a high-tech dimpled bottom, we've re-lofted the bottom to give PAVATI drift boats less draft. Less draft equals a higher riding drift boat. You'll notice the first time you row a PAVATI that you'll hit fewer rocks. And since you're riding higher in the water, cross currents don't push you around. The fiberglass drift boat builders talk about how their boats slide over rocks. PAVATI drift boats float over rocks. You'll be amazed at how shallow and stable a drift boat can be.

We have 3 methods of approach for coating the dimpled bottom of your Pavati drift boat.
  • 1. Powder Coating
  • 2. Advanced Kevlar Bottom
  • 3. UMHW Bottom (Ultra-high-molecular-weight polyethylene)
Read more below!


Powder Coated Bottom

Powder coating is a type of coating that is applied as a free-flowing, dry powder. The main difference between a conventional liquid paint and a powder coating is that the powder coating does not require a solvent to keep the binder and filler parts in a liquid suspension form.

The coating is typically applied electrostatically and is then cured under heat to allow it to flow and form a "skin". The powder may be a thermoplastic or a thermoset polymer. It is usually used to create a hard finish that is tougher than conventional paint.


Advanced Kevlar Bottom

Bare aluminum bottoms grab rocks, don't slide very well, and are notorious for being noisy. We have solved all of the above. After doing some research on new materials available we stumbled upon a Kevlar coated polymer. It's original intention was for the inside of dump truck beds in rock quarries. It's so hard you can almost take a grinder to it. Police departments are even using it on the inside of their squad car doors for bullet protection.

PAVATI is the first to use it on the bottoms of drift boats but we expect it to be an industry standard very soon. It slides over rocks and takes a beating, then asks for more. An added bonus is it deadens sound by up to 80%. PAVATI has put an end to the days of noisy aluminum drift boats. Now you can have your cake and eat it too. Another first for PAVATI.


UHMW Bottom

It has extremely long chains, with molecular weight numbering in the millions, usually between 2 and 6 million. The longer chain serves to transfer load more effectively to the polymer backbone by strengthening intermolecular interactions. This results in a very tough material, with the highest impact strength of any thermoplastic presently made. It is highly resistant to corrosive chemicals, with exception of oxidizing acids.

It also has extremely low moisture absorption, has a very low coefficient of friction, is self-lubricating, and is highly resistant to abrasion (15 times more resistant to abrasion than carbon steel). Its coefficient of friction is significantly lower than that of nylon and acetal, and is comparable to that of Teflon, but UHMWPE has better abrasion resistance than Teflon


12 POSITION OARLOCK BLOCK - STANDARD

When you get your new PAVATI drifter you want everything to be perfect. Having the oar locks in the right place is essential. Eight different positions ensures that you will get the most leverage you can for those times when you need all the horsepower you can muster.

If you want to fish 1-1-1 (three in a row), for the popular side drifting technique, you may want to move your row seat forward to balance the boat. This means you will need to move the oar locks too. No matter how you want to set your boat up, fly fishing, bait fishing, or pulling plugs, our simple clip locks allow you to move the oarlocks to the optimum position in seconds.

On top of that we offer you "Kenny Helfrich's" stainless steel - super strong - oar locks. Kenny, a third generation Eugene Oregon area guide, developed these oar locks to not only be super strong but to stop your oar from climbing up the side of the oar lock with each stroke as most do. If you've rowed a boat much you've probably noticed the thump, thump, after each stroke. That noise is the oar dropping back to the bottom of the oarlock. Also, in a real tough situation, these oar locks are designed to flex enough to allow your oars to pop out of these oar locks. Kenny says, "These are the last pair of oar locks you will ever own." -- That's good enough for us.


GRAB HANDLES

PAVATI has added handy grab handles to the sides of the hull. Just below the gunnel rail near the oar locks, we have programmed in computer cut holes. These make it easy to pick the boat up or portage around logs/skinny spots in the river.
MOTOR READY TRANSOM

All PAVATI drifters come with a motor ready transom ready to except up to a 10HP gas or electric motor. Unique to our transom is the inset "motor lock". Never again do you have to worry about your motor falling off on that bumpy washboard dirt road. Another PAVATI first.


"THE TRUTH" SCALES

How many times have you wanted to know how long your fish was to see if it was legal to keep? Or just to brag about? In the past you had to drag out a tape measure, if you could find it, or just guess. Not only was this inconvenient but a lot of fish died because we didn't get them back in the water in time. PAVATI continues to set the pace with scales on both sides of your drift boat as standard equipment. The computer numerical controlled (CNC) designed, "THE TRUTH", tape measures make measuring fish and leaders a one man job. Measure your fish in seconds and let it go. Up to 60 inches. PAVATI drift boats not only catch fish, they save them too! Not a sticker, it's engraved right in the aluminum. Great for measuring leaders too. Another PAVATI first.




PAVATI's Rod Holder Brackets (Gunnel Grabber)

Rod holders are always a pain in drift boats. PAVATI went after this problem with a raised butt holder to keep your reels off the floor, minimizing damage. Attaching rod holders to a PAVATI couldn't be any easier. No tools and no time. Check out the video.

PAVATI's Rod Butt Holder with Leader Roller

With PAVATI's adjustable floor system, you can adjust where the rod holder goes and take it out in seconds when you go crabbing or just don't need it. To top it off we found a neat place to put a leader roller. Do we need to say it again? Another PAVATI first.


SIDE FOOT RELEASE ANCHOR SYSTEM

Our exclusive offset foot release is the easiest and safest anchor release system available. We improved on the old foot stomp release by moving the foot pad off to the side -- not under your feet. This gets it out fo the way of fishing lines and keeps you from stomping on it by accident (but still allows you to get to it quickly). This foot release allows you to let the anchor go just by tapping it with your foot. Allowing you to stay on the oars until your drift boat has stopped. Pavati has multiple anchor release options to choose from. Give us a call and we can figure out which system will work best for you.

CUSTOM BENTLEY SEATS W/ DRY BOXES

This picture shows the seats set up for a family cruise down the river or for reel fisherman, casting on each side of our drift boat.

This style of seatbox not only allows you to move the seats around to your liking but gives each person a storage area for their lunch or a jacket. We like this system because it gives you plenty of room to turn the whole seat around for trolling and walk-through access to the rest of the boat. All seats can be easily moved and locked down in the back for fly fishing in just a couple of minutes.


Tackle Tower/ Rod Holder Combo

Pavati's Tackle Tower and Rod Hold Combo is one of the newest accessories that we offer. It supplies you with three locations to store your tackle boxes filled with lures, leaders, bobbers, knives, etc... And is also a combination Pavati Rod Holder.

Pizza Oven Compartment

This storage space is directly above the heater and doubles as an oven for cooking and warming foods plus the warming up of other items such as bait towels or rocks to warm up and put in your pockets on those ice cold fishing nights. It also acts as a heat shield protecting the deck preventing it from getting too hot when running the heater full blast.


In-Floor Fish Box

When Pavati marine first introduced the first true full level floor a couple of years ago, we never imagined what ideas would spring from it. New for 2011, PAVATI is proud to offer the first in-floor fish box.

It adds no weight to the boat, keeps fish fresher than ever by putting them out of the sun and directly against the bottom of the boat. The rivers cold temperature is transmitted directly to your fish. It also cleans very quickly an easily. A great option if you catch and keep big fish.


Drift boat specificationss: (PAVATI Marine makes many standard sizes of drift boats, the boat specs shown are the most popular sizes. For specifications on other sizes please call.)
Model: 17x61 Legacy
Center Length: 17'
Bottom Width: 61"
Beam: 90"
Oarlock Height: 25"
Aluminum Grade: 6061 T6
Bottom Thickness: .125
Side thickness: .100
Hull Weight: 190 lbs
Motor: 10 h.p.
Model: 16x61 Legacy
Center Length: 16'
Bottom Width: 61"
Beam: 90"
Oarlock Height: 25"
Aluminum Grade: 6061 T6
Bottom Thickness: .125
Side thickness: .100
Hull Weight: 180 lbs
Motor: 10 h.p.
Model: 16x55 Legacy
Center Length: 16'
Bottom Width: 55"
Beam: 85"
Oarlock Height: 25"
Aluminum Grade: 6061 T6
Bottom Thickness: .125
Side thickness: .100
Hull Weight: 180 lbs
Motor: 10 h.p.


                           

Customize your Pavati Drift Boat with a boat motor of your choice.


Pavati's Lifetime Warranty

Our Parent company Highway Products Inc. has been standing behind its products for over 30 years with an industry exclusive Lifetime warranty, and we have no intention of doing anything less with PAVATI. That's why we offer the only transferable lifetime warranty in the boat world today. Our warranty isn't void as soon as you leave the state or sell it. If you buy a PAVATI, even if it's used, we will stand behind our work.